Fasteners & Hardware
Disc brake pad adjuster tab washer
Disc brake pad adjuster tab washer. For all Lambrettas equipped with original disc style brakes...
$2.00
Disc locating pin
Disc locating pin, for replacing the worn out pins in original Lambretta front disc brake. A tr..
$9.00
End cap hardware kit: Series 3
Hardware that goes through all the endcaps of a Series 3. Kit contains: 6 m4 x 20 screws ..
$10.00
Engine circlip kit
This handy bagged kit contains the correct circlips you need to overhaul a Lambretta engine. It does..
$12.00
Exhaust nut: 7mm, Brass
This special nut is suitable for use on the studs that secure a Lambretta exhaust...
$2.00
Flywheel and cylinder shroud hardware kit: Series 1-3
To install both the cylinder and flywheel/fan shroud on Series 1-3, DL/GP. Consists of: 7 m5 ..
$5.00
Flywheel and head cowl HEX kit
This handy kit contains the correct number of hex set screws and washers to fit your head and flywhe..
$4.00
Front axle half nut washer and side panel lever washer
Front axle half nut washer. This washer goes between the half nut and the back plate on drum type fr..
$0.45
Front axle locating washer, stainless
This washer sits in your fork link to hold your axle (and hub!) in place, so it is important it is..
$5.00
Front axle locating washer, zinc
This washer sits in your fork link to hold your axle (and hub!) in place, so it is important it is..
$2.00
Front floor rails hardware kit: Series 3
For installing the 4 front alloy channels on Series 3 and DL. Consists of: 6 m4 x 10 screws..
$12.00
Front mudguard hardware kit: Series 3
This kit includes: 2 m5 x 20 screws for the bottom (under aluminum channel) 2 m5 nuts for ab..
$5.00
Gear selector wishbone screw
This fastener can specifically be used for the shifter wishbone, eliminating the need for a 9mm sock..
$0.45
Grease nipple: M6 x 1.00 11 mm wrench
Grease nipple: M6 x 1.00 11 mm wrench Used on some front hub backplates, fork links, fork link bolt..
$2.00
Grease nipple: M8 x 1.25 11 mm wrench
Grease nipple: M8 x 1.25 11 mm wrench Used on the front hub of some Lambrettas. ..
$2.00
Grease nipple: M8 x 1.25 14 mm wrench TECALEMIT D/LD
Grease nipple: M8 x 1.25 14 mm wrench TECALEMIT D/LD..
$5.00
Handlebar light switch housing screw
Used to secure the Lambretta light switch housing to the headset. You need two per scooter. M6x12..
$0.45
Handlebar light switch screws: Series 1-3, GP/DL, Serveta
Kit for securing the light switch to the handlebar. Consists of: 2 m3 x 25 screws ..
$2.00
Headlight rim hardware kit: Series 1, Series 2 Li/TV, Series 3 Li
Headlight rim hardware kit: Series 1, Series 2 Li/TV, Series 3 Li. Kit consisting of: 4 m4 x 1..
$2.00
Headlight rim hardware kit: Series 3 LiS/TV/SX
Kit for securing the headlight rim on all Series 3 LiS, TV and SX models. Kit consists of: 4 ..
$1.00